C27 ACERT Land Mechanical Drilling Engine
Cat C27 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C27 ACERT engines to deliver excellent performance with low operating costs and emissions. This is an ideal engine for land mechanical drilling applications such as mud pump drives. Cat C27 ACERT™ Industrial Diesel Engine. Ratings: 597-858 bkW (800-1150 bhp) @ 1800-2100 rpm meet U.S. EPA Tier 2 equivalent emission standards.
Engine Specifications
Maximum Rating
Emissions
Displacement
Minimum Rating
Bore
Stroke
Rated Speed
Aspiration
Governor and Protection
Engine Weight - Net Dry
Oil Change Interval
Rotation from Flywheel End
Flywheel and Flywheel Housing
Flywheel Teeth
Capacity for Liquids
Minimum Cooling System - Engine Only
Dimensions
Length
Width
Height
Standard Equipment:
-
- Air Inlet System
-
- Dual turbochargers side or rear mounted — inlet 152.4 mm (6 in.) hose connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature, pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
-
- Cooling System
-
- Thermostats and housing — outlet LH vertical orientation
- Jacket water pump — gear-driven, centrifugal RH
-
- Exhaust System
-
- Exhaust manifold — dry, heat shields
- Dual turbo — rear turbo exhaust, full marmon connection 127 mm (5 in.), maximum load 10 kg for direct
- Water-cooled center sections
-
- Flywheels And Flywheel Housings
-
- SAE No. 0 or SAE No. 1
- SAE standard rotation
-
- Fuel System
-
- MEUI system
- Fuel filter, RH ( 2 micron high performance)
- Fuel transfer pump
- Fuel priming pump (optional electric priming pump)
-
- Lube System
-
- Crankcase breather — rear mounted
- Oil cooler — RH
- Side turbo — oil filler in RH front gear case
- Rear turbo — oil filler in RH valve cover
- Oil level gauge — RH
- Oil filter — RH
- Oil pan rear sump
-
- Mounting System
-
- Front support — narrow
-
- Power Take-offs
-
- Crankshaft pulley — 203.2 mm (8 in), 5 grooves 15.9 mm (.63 in) wide; 292.1 mm (11.5 in.) 1 groove 15.9 mm (.63 in.) wide
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins, sockets)
Optional Equipment:
-
- Air Inlet System
-
- Air lines
- Air cleaners
- Precleaners
-
- Charging System
-
- Battery chargers
- Charging alternators
- Alternator mountings
-
- Circuit Breakers
-
- Circuit breaker mounting
-
- Cooling System
-
- Blower fans
- Suction fans
- Radiators
-
- Exhaust System
-
- Muffler
-
- Fuel Systems
-
- Electric fuel priming pump
-
- Instrumentation
-
- Gauges and instrument panels
-
- Lube System
-
- Lubricating oil
- Oil pan
- Oil filter
-
- Mounting System
-
- Engine supports
-
- Power Take-offs
-
- Hydraulic pump drives
- Pulley
- Auxiliary drive
-
- Starting System
-
- Electric starting motor
- Battery sets - 24V
- Battery cable
- Battery rack
- Starting aids
-
- Packaging
-
- Overseas preservation
- Storage preservation
- Export packaging
Contact Us
Get A Quote
Thank you for your interest in Mustang Cat. We are here to help you in any way that we can. If you have a question, need equipment advice or just need additional information, we want to hear from you. You can email, phone or fill out the form below and we will be happy to connect with you.