Black banner

C32 ACERT™ Water-Cooled Manifold Engine

C32 ACERT™ Water-Cooled Manifold Engine

Cat C32 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C32 ACERT engines to deliver excellent performance with low operating costs and emissions. Applications powered by C32 ACERT engines include well stimulation pumping, pump skids, nitrogen units, acidizing units, blenders, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C32 ACERT water-cooled manifold engines, with ratings: 597-914 bkW (800 1125 bhp) @ 2100 rpm meet IMO Tier II, U.S. EPA Marine Tier 2, and U.S. EPA Non-road Tier 2 equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.

General Specifications

Maximum Rating

1225BHP

Displacement

1960.5in³

Minimum Rating

800BHP

Aspiration

Turbocharged-Aftercooled

Flywheel and Flywheel Housing

SAE No. 0 or SAE No. 1

Flywheel Teeth

136

Stroke

6.4in

Bore

5.7in

Emissions

Emissions

EPA and CARB Non-Road Mobile Tier 2, EPA Marine Tier 2, IMO Tier II, China Stage III

Dimensions

Length

76.1in

Width

57in

Height

54.7in

Weight

5084lb

Standard Equipment:

  • Air Inlet System
    • Connections configured for SCAC and ATAAC (Air-to-AirAftercooled) or remote heat exchanger
  • Control System
    • ADEM A4 electronic control module
    • Electronic governing, PTO speed control
    • Customer programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Automatic fuel temperature compensation
    • Programmable low and high idle
    • Electronic diagnostics and fault logging
    • Engine monitoring system
    • SAE J1939 broadcast (diagnostic and engine status)
  • Cooling System
    • Gear-driven centrifugal jacket water pump — RH
    • Integrated thermostat and housing
    • Engine oil cooler
    • Optional installed transmission oil cooler
    • Optional aftercooler and auxiliary water pump
    • Optional jacket water heat exchanger
  • Exhaust System
    • Exhaust manifold — watercooled
  • Fuel System
    • MEUI
    • Fuel priming pump
    • Fuel transfer pump
    • Primary and secondary fuel filter — RH configured for remote mounting (installed RH on shipping plate)
  • Flywheels And Flywheel Housing
    • SAE No. 0 or SAE No. 1 flywheel iron housing
    • SAE No. 0 or SAE No. 1 flywheel
    • Optional transmission adapter
  • Lube System
    • Crankcase breather
    • Oil filter — RH standard, optional LH or remote mount service
    • Oil level gauge — RH standard, optional LH or dual service
    • Oil filler — RH standard, optional LH or dual service
    • Shallow oil pan, rear sump
  • Mounting System
    • Trunnion front support
    • Vertical and horizontal pads on rear flywheel housing
  • Protection System
    • 24 volt electronic
    • Engine overspeed with optional air shut-offs with indicators
    • Low engine oil pressure
    • Fuel filter restriction
    • Fuel temperature
    • High engine coolant temperature
    • Low engine coolant temperature
  • General
    • Vibration damper
    • Lifting eyes
    • Optional customer wiring connector
    • Service tool connector
    • Paint — Cat yellow
    • Optional two-part primer and mastic caulk

Optional Equipment:

  • Air Inlet System
    • Air cleaner
    • Air inlet adapters
    • Turbocharger outlet adapters
    • Air lines
  • Charging System
    • Battery chargers
    • Charging alternators
    • Alternator mounting
    • Circuit breakers and mountings
  • Cooling System
    • Dry charge coolant conditioners
    • Thermostat housing
    • Coolant level sensor
    • Radiator
    • Blower fans
    • Suction fans
    • Fan adapters
    • Fan drives
  • Emissions
    • IMO certifications
  • Exhaust System
    • Elbows
    • Mufflers
  • Fuel Systems
    • Electric fuel priming pump
  • Instrumentation
    • Customer management device
    • Interconnect harness
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Oil service side
    • Oil level gauge
    • Oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support — front
    • Engine support — rear
  • Power Take-offs
    • Auxiliary drive
    • Damper pulley
    • Hydraulics gear pumps
  • Protection System
    • Mechanical shutoffs
    • Solenoid shutoffs
  • Starting System
    • Electric starting motors - 12V, 24V
    • Battery sets - 24V
    • Battery cable
    • Battery rack
    • Starting aids
  • Transmission Arrangement
    • Transmission water lines
    • Transmission cooler

Contact Us

Get A Quote

Thank you for your interest in Mustang Cat. We are here to help you in any way that we can. If you have a question, need equipment advice or just need additional information, we want to hear from you. You can email, phone or fill out the form below and we will be happy to connect with you.

    true I agree to all the terms and conditions

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.